COVID-19 Montana 3D Printed Mask
The COVID-19 pandemic has caused a worldwide shortage of personal protective equipment (PPE) for hospital staff and the general public. I’ve been experimenting with printing different 3D mask designs, but most of them had to be custom formed after printing or just didn’t work. Then, I found the following short video by Dr. Dusty Richardson, MD on the Montana Mask:
That video led me to these websites, which contains additional info about the masks and how to make them:
Billings Clinic 3D Printed Surgical Mask
The URLs on that website to download the STL files required for 3D printing didn’t resolve, but I was able to find them elsewhere and they can be downloaded here.
3D Printer Settings
I used 3D Simplify and the following settings to print these masks:
- Filament Type: PLA
- Infill: 0.25
- Layer Height: 0.1 mm
- Rotate the mask image so that the front lies flat on the printing bed
- No supports
You can find the 3D Simplify factory file modified with the above settings here
Ready to Print x3g Files
If you have a Makerbot dual extruder or compatible printer, I’ve created ready to print x3g files that include both the mask and the filter frame. I also scaled down the original size mask (large - 100%) to a medium size (95%) and small size (90%). You can place the appropriate x3g file directly on an SD card and print - no computer required:
Large Mask and Filter Frame printed using Left Extruder
Large Mask and Filter Frame printed using Right Extruder
Medium Mask and Filter Frame printed using Left Extruder
Medium Mask and Filter Frame printed using Right Extruder
Small Mask and Filter Frame printed using Left Extruder
Small Mask and Filter Frame printed using Right Extruder
Each mask and filter frame takes about 4 hours to print, and I’m currently printing 3-4 a day.
Installing and Replacing the Filtration Material
Most suppliers of N95 filtration material such as this one are either out of stock or just supplying first responders, who should get preferential treatment. I’m using blue shop towels as well as the filtering material from 3M Filtrete 1500 furnace filters. Here’s a comparison of what common materials filter:
- N95 masks: 0.1 - 0.3 microns
- Blue shop towels: 0.3 microns
- 3M Filtrete material: 1-3 microns
- Cloth face mask: 20 microns
- Coffee filter: 20 microns
While blue shop towels do a good job of filtering small particles, they’re fairly restrictive. The 3M Filtrete material is easy to breathe through even when doubled up. I plan to use the blue shop towel for short trips to the store, and 2 layers of 3M Filtrete material for extended use.
Cut the filtration material to the following size to use with the mask, and use 2 layers:
- Large: 2.75" x 2.75"
- Medum: 2.6" x 2.6"
- Small: 2.5" x 2.5"
Make sure to mark the airflow direction on the 3M filter before removing the material, and face the tip of the arrow side towards the inside of the mask. Wrap the material around the small square frame and press into place from the inside of the mask.
Installing and Testing the Seal
I used 5/16-in White Window Weatherstrip and Loctite Super Glue to make a seal around the edge of the mask. This video shows how to install it properly.
You can test the seal by putting the mask on, sealing the opening by holding your hand over it, and trying to breath in and out to see how much air enters or escapes. With the large mask, I had a pretty good seal with no weather stripping, and a complete seal with weather stripping. For men, shaving will help.
Installing the Rubber Straps
With everyone making cloth masks, traditional elastic materials are hard to come by. I’m using 0.2" natural latex rubber tubing. Cut two lengths 15" long. Cutting on an angle makes it easier to thread the tubing through the eyelets in the mask. Put one on each side, and if you want to wrap the tubing around your ears to hold the mask in place, you’re done:
Adjust the straps by pulling the slack through the eyelet. If the mask won’t stay in place, cut another 11" piece of surgical tubing and use it to tie between the existing straps to wrap around your head:
I'm curious how the surgical tubing worksReplyDelete
Surgical tubing didn't work as a seal but worked great for the straps. Now this is back ordered as well. Using women's hair ties, hair bands, and whatever stretchy material I can find for straps now.ReplyDelete
I am a full-on neophyte regarding 3D printing. The choices are more than a little bewildering. I've looked at da Vinci, Monoprice. and Flashforge. Any suggestions regarding a good choice for a first printer that can handle the Montana Mask? What size build platform do you recommend to accommodate the large mask?ReplyDelete
Lastly, the FlowmarkHighTech folks seem to strongly suggest (without actually saying it in so many words) that the mask filter material that they offer should not be considered to meet N95 requirements. Is that because it has not been submitted for testing or because they know that it is not N95-compliant? I've asked but have no reply currently.
Sorry to be grilling you on all of this. But I'm the new kid on the block and so am playing catchup. And thank you for all that you've done to help the rest of us get up to speed as quickly as possible.
BTW, if/when you choose to reply to my questions, email is an option, rather than posting here. And if you go that way, I'd ask that you use:ReplyDelete
rather than my gmail address. Thanks.
I use a Qidi dual nozzle 3D printer. The platform on this printer is 6" x 9". I can't answer to the Flowmark Hightech statements - you'd have to ask them.Delete